Return to the Square Foot Gardening Forum | Post a Follow-Up

 o
cold frame pitch

Posted by has55 7 (My Page) on
Fri, Nov 30, 12 at 20:22

I would like to build a cold frame out of pvc that will open and close manually. I found some plans on pvcplan.com. I'm not a carpenter. I have been able to adjust the plans to my 4x4 sqf bed , except I can't figure out how to make a ptich whereas the two sides come to the middle equally. See plan below. can anyone share with me how to figure out the proper height, width and length. I want it to be 2ft high in the middle.


Follow-Up Postings:

 o
RE: cold frame pitch

To find the pitch dimensions (triangle), use the Pythagorean Theorem, which is A^2+B^2=C^2 (A,squared + B,squared = C squared).

As an example:
You have a 4'x4' bed, your roof is 2' high at center of bed. So your triangle (one half of your roof) has a base of 2, your hight is 2, so

2sq+2sq = Csq
4+4 = Csq
8 = Csq
square root of 8 = C
2.83' = C

You can do the same if you want to use inches.
24sq+24sq = Csq
576+576 = Csq
1152 = Csq
square root of 1152 = C
33.94" = C

That get's you a roof that is exactly two foot high by 4 foot wide, with a 45deg joint at the top.

But, I read your post that you want the whole thing to be 2 foot high at the center, so using the same formula, your A is still 2', but your B is 2' minus the height of your base box. To make it easy, say your base box is 1', therefore leaving you with a 1' high roof at the center.
So,
2sq+1sq = Csq
4+1 = Csq
5 = Csq
sqr of 5 = C
2.24' = C

Inches:
24sq+12sq = Csq
576+144 = Csq
720 = Csq
sqr of 720 = C
26.83" = C

NOTE: When your A&B lengths do not match, you will not have a 45deg angle at the top, which might be a problem with finding a T-Angle joint that has the angle you need.

If you need further help, let me know and I'll dimension it up in Autocad and post a pic.


 o
RE: cold frame pitch

have Thank you. That was extremely helpful. I worked 12-14 hrs shift and not wrote a follow up that was decided on saturday. I was going to post today a change in plans via my wife suggestion, but you beat me to the punch. Your answer and your time is much appreciated. Please forgive my delay with my posting.

After I showed her the above plan with the a frame roof versus a hoop house that would open up, she voiced she like the smoother round look since the garden is in our front yard. I part of the movement that's turning their grass into a garden, to something I can eat. I live in North Tx where the drought is alive and doing well.
So I placed 1/2" PVC pipe on top of the wood and inserted into 1/2" 3 way connector on all 4 corners. Then I cut a 90" piece of 1/2" pipe into 2- 45" pieces and have connected them in the middle with a 1/2" T connector. I placed both ends into the top side of a 3 way connector on each end. one side corner and connected the two T connectors with a 1/2 pipe for stability. The pipe shows tension , because the end rises approx 1/2" off the corner. i believed this will be remedy when I screw upright snap clamps to the wood to hold it place.
It will have a handle and a 3/4 snap clamp attached to 1/2 pvc pipe on one side so I can lift it up to open it to prevent over heating and get to the food. I will send a picture. You may have a better idea.
This look was acceptable to my wife and seem less expensive and time consuming. I glueing the base pipe to the 3 way corner to prevent slippage.
I can't figure out how to add more than one photo per post. So I will add the others per post.

AUSTIN


 o
RE: cold frame pitch

4th and last picture. different view.


 o
RE: cold frame pitch

2nd . it will open. Not snap down or hinges applied. NO plastic covering yet.


 o
RE: cold frame pitch

3rd picture. didn't hit submit button earlier. anyway different view.


 o
RE: cold frame pitch

Lookin' good! You might end up having to reinforce the roof in a couple areas. Keep an eye out for the plastic sagging between your two hoop walls, and also look for overall structure sagging at the hoops themselves. You have horizontal cross brace for the hoops at the top, but the only vertical bracing is the hoops themselves. Depending on if you get rain, snow, wind, ect is if you need to add additional support. Other than those thoughts, looks like you are on the right track.

On a side note, during the non-cold season, you can tie a stretch of grid fence (cow fence) over the frame and it makes a decent trellis for vine plants (if you plant any). But then you definitely would want to look at adding a vertical reinforcement section at the sides, part of the hoops.

Anyways, experiment away and have some fun with it. Make some artistic shapes out of the extra pvc, paint, and use as garden deco.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Square Foot Gardening Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here